John Deere BC96 96-Inch Angle Broom
Overview
The John Deere BC96 is a 96-inch angle broom from the Worksite Pro attachment line for full-size Deere skid steers sweeping large paved areas and construction sites. The 8-foot drum covers maximum area per pass on highway pull-offs, large parking areas, and industrial floors. John Deere factory brooms are optimized for Deere machine hydraulics. Available through Brandt and John Deere dealers across Canada.
Canada Availability
Best for: large paved areas, construction sites, industrial floors
Compare with: Blue Diamond 84-Inch Skid Steer Angle Broom · Blue Diamond 96-Inch Angle Broom for Large Skid Steers · Blue Diamond 96-Inch Angle Broom for Skid Steers
Key Facts
- Working width: 96 inches (8 feet)
- Model: BC96
- Type: angle broom
- Series: John Deere Worksite Pro
- Application: large paved areas, construction sites, industrial floors
- Weight: 400–1200 lbs
- Hydraulic flow: 15–25 GPM
Is This Right For You?
Buy if
- You clean up debris, sand, and small material from hard surfaces like concrete, asphalt, or warehouse floors
- Spring road sand cleanup in Canadian parking lots is a core task for your machine
Skip if
- You need to collect the material, not just move it — an angle broom side-casts debris into a windrow
- Fine dust or regulated material (silica) requires containment — an angle broom disperses it
Also consider
- Pickup broom if you need to collect material rather than side-cast it
- Street sweeper or vacuum attachment if dust control is a regulatory requirement
Designed for John Deere machines but mounts to any skid steer or CTL with a universal SSQA quick-attach plate.
About John Deere in Canada
John Deere attachments are available through an extensive Canadian dealer network, ensuring local service, parts availability, and warranty support coast to coast. Designed to pair with JD machines but compatible with any skid steer via universal quick attach.
Care & Maintenance
- Inspect broom fill length after every 20 hours of use — bristles below minimum length drag rather than sweep, waste time, and mask the fact that you need a replacement
- Clean debris wrapped in the drum core after every extended session — wire, hair, and root cause drum imbalance and stress the hydraulic motor bearings
- Grease drum bearing end caps monthly during active use periods
- Check hydraulic motor connections and angle cylinder fittings weekly — broom motors work hard and connection fittings loosen over time
- Store on end or off the ground so bristle fill doesn't take a permanent set under drum weight — brooms stored drum-down develop flat spots in the fill that affect sweep quality
How to Connect
- Attach broom frame using Bob-Tach
- Connect hydraulic couplers for rotation motor
- Verify rotation direction (forward-sweep or reverse-sweep per job)
- Adjust broom angle if applicable — most have manual tilt adjust
Ready to Buy in Canada?
Pricing varies by region and dealer stock levels change seasonally. For current availability and a real quote, contact a local dealer.
Find a Dealer Near You →Complete the job — you might also need:
More from John Deere
John Deere Worksite Pro 4-in-1 Combination Bucket
Standard FlowJohn Deere's Worksite Pro 4-in-1 bucket is a hydraulic combination attachment for John...
View product →
John Deere 30-Inch Auger for Skid Steers in Canada
Standard FlowThe 30-inch-inch auger bit drills post holes, footings, and fence lines in Canadian soil...
View product → John Deere 36-Inch Auger for Skid Steers in Canada
High FlowThe 36-inch-inch auger bit drills post holes, footings, and fence lines in Canadian soil...
View product → John Deere CM48B Cement Mixer
Standard FlowThe John Deere CM48B is a smaller-capacity cement mixer in John Deere's Worksite Pro...
View product →✓ Last checked: March 2026