John Deere Worksite Pro PR96B Power Rake
Overview
A 96-inch hydraulic power rake in John Deere's Worksite Pro line. Built for landscaping, seedbed preparation, and finish grading on construction sites. The rotor uses adjustable scarifying teeth to break up clumps and move debris to the side trough, leaving a ready surface in a single pass. Available in Canada through Brandt and John Deere dealers with full warranty support.
Canada Availability
Best for: landscaping, seedbed preparation, site grading, lawn renovation
Compare with: Berlon 96 Inch Skid Steer Power Rake · Blue Diamond 84-Inch Skid Steer Power Rake · Blue Diamond 90-Inch Power Rake for Skid Steers
Key Facts
- Working width: 96 inches (244 cm)
- Drive: hydraulic, standard flow
- Application: landscaping, seedbed preparation, site grading, lawn renovation
- Adjustable scarifying teeth for soil type and finish quality
- Side troughs collect debris and clods during operation
- Compatible with John Deere skid steers and compact track loaders with SSQA mount
- Weight: 800–2400 lbs
- Hydraulic flow: 15–30 GPM
Is This Right For You?
Buy if
- You're breaking up compacted gravel roads, hardpan, or packed aggregate before regrading
- Your site has frost-heaved or rutted surfaces that need aggressive tine action before re-spreading
- You need to loosen material before a final grading pass — scarifiers prep the surface efficiently
Skip if
- You're finishing a prepared seedbed — a standard power rake with finer tines does that job better
- Your soil is already loose — scarifier tines dig too aggressively and will over-till
Also consider
- Standard power rake for final seedbed prep and debris removal
- Landplane for final levelling after scarifying
Designed for John Deere machines but mounts to any skid steer or CTL with a universal SSQA quick-attach plate.
About John Deere in Canada
John Deere attachments are available through an extensive Canadian dealer network, ensuring local service, parts availability, and warranty support coast to coast. Designed to pair with JD machines but compatible with any skid steer via universal quick attach.
Care & Maintenance
- Inspect rotor teeth after each use — chipped or missing carbide dramatically reduces grading quality and throws the rotor off balance
- Grease rotor shaft bearing housings at each end after every 8 hours of use — most premature bearing failures trace back to insufficient lubrication intervals
- Clean packed soil from rotor teeth and the housing after every job — built-up soil throws the rotor out of balance and restricts rotation
- Replace worn teeth in matched sets — mixing old and new teeth across the rotor causes uneven cutting and vibration that stresses the drive
- Inspect hydraulic motor drive connections and belt tension (if belt-driven) weekly during active season
How to Connect
- Attach frame using Bob-Tach
- Connect hydraulic rotor circuit
- Adjust rotor depth by lowering carefully — engage at surface before penetrating soil
- Set material deflector angle if applicable
Ready to Buy in Canada?
Pricing varies by region and dealer stock levels change seasonally. For current availability and a real quote, contact a local dealer.
Find a Dealer Near You →Complete the job — you might also need:
More from John Deere
John Deere Worksite Pro 4-in-1 Combination Bucket
Standard FlowJohn Deere's Worksite Pro 4-in-1 bucket is a hydraulic combination attachment for John...
View product →
John Deere AB60B 60 Inch Skid Steer Angle Broom
Standard FlowThe 60-inch-inch angle broom sweeps paved and gravel surfaces — parking lots, yards,...
View product → John Deere AB72B 72 Inch Angle Broom
Standard FlowThe 72-inch-inch angle broom sweeps paved and gravel surfaces — parking lots, yards,...
View product →
John Deere 30-Inch Auger for Skid Steers in Canada
Standard FlowThe 30-inch-inch auger bit drills post holes, footings, and fence lines in Canadian soil...
View product →✓ Last checked: March 2026