John Deere Worksite Pro DB72 Dozer Blade
Overview
A 72-inch hydraulic dozer blade in John Deere's Worksite Pro line. The DB72 is a straight blade — it grades and pushes material without angling. For Canadian oilfield site prep, road building, and frost-heave repair work where you need to push material in a straight line without the bulk or complexity of a 4-way blade. Hydraulic float mode lets the blade follow contours rather than bridging. Available through Brandt.
Canada Availability
Best for: site clearing, road building, frost-heave repair, backfill
Compare with: Berlon Industries 84-Inch Dozer Blade for Skid Steers · Blue Diamond 72-Inch 6-Way Skid Steer Dozer Blade · Blue Diamond 84-Inch 6-Way Dozer Blade Skid Steer
Key Facts
- Working width: 72 inches (183 cm)
- Blade type: straight blade
- Hydraulic float mode for contour-following grading
- Application: site clearing, road building, frost-heave repair, backfill
- Hydraulic flow requirement: standard auxiliary hydraulics (approximately 13–20 GPM)
- SSQA (universal skid steer quick attach) mount
- Compatible with John Deere skid steers and compact track loaders
Is This Right For You?
Buy if
- You need to angle the blade left/right for ditch work, pushback, or casting in a specific direction
- Your site work involves both straight pushing and angled clearing
Skip if
- You only push in one direction — a straight blade is lighter, simpler, and cheaper
- Precision finish grading matters — a land plane or box blade gives a better finished surface
Also consider
- 6-way blade for hydraulic tilt control in addition to angle
- Box blade if the goal is levelling a surface rather than pushing material
Designed for John Deere machines but mounts to any skid steer or CTL with a universal SSQA quick-attach plate.
About John Deere in Canada
John Deere attachments are available through an extensive Canadian dealer network, ensuring local service, parts availability, and warranty support coast to coast. Designed to pair with JD machines but compatible with any skid steer via universal quick attach.
Care & Maintenance
- Grease all hydraulic cylinder pin fittings before every use session — dry pins accelerate wear in the cylinder bores and cause premature side-loading
- Inspect the cutting edge for wear or deformation after hard use — replace bolt-on edges when worn to avoid transferring impact to the blade frame
- Check hydraulic coupler connections for leaks weekly — dozer blade circuits cycle frequently and coupler seals wear faster than on less-cycled attachments
- Inspect tilt and angle cylinder rod seals for leaks after use in abrasive or sandy soil — grit scoring a rod seal causes accelerating internal leakage
- Clean the blade face and frame before storage — mud pockets hold moisture against bare steel and cause rust pitting during off-season storage
How to Connect
- Attach blade frame to Bob-Tach
- If 6-way blade: connect tilt and angle hydraulic circuits (both sides)
- Test all blade movements (up/down, tilt left/right, angle) before working
Ready to Buy in Canada?
Pricing varies by region and dealer stock levels change seasonally. For current availability and a real quote, contact a local dealer.
Find a Dealer Near You →Complete the job — you might also need:
More from John Deere
John Deere Worksite Pro 4-in-1 Combination Bucket
Standard FlowJohn Deere's Worksite Pro 4-in-1 bucket is a hydraulic combination attachment for John...
View product →
John Deere AB60B 60 Inch Skid Steer Angle Broom
Standard FlowThe 60-inch-inch angle broom sweeps paved and gravel surfaces — parking lots, yards,...
View product → John Deere AB72B 72 Inch Angle Broom
Standard FlowThe 72-inch-inch angle broom sweeps paved and gravel surfaces — parking lots, yards,...
View product →
John Deere 30-Inch Auger for Skid Steers in Canada
Standard FlowThe 30-inch-inch auger bit drills post holes, footings, and fence lines in Canadian soil...
View product →✓ Last checked: March 2026